New PP Calibration

Post Reply
barnabeflores
Posts: 16
Joined: Sat Nov 17, 2018 5:47 am

New PP Calibration

Post by barnabeflores »

Hello, I just bought a new PP V2 and updated with the latest firmware.

I loaded the following data in to the Isaac software:

- rider weight: 73kg

- bike weight: 10 kg

Did the out and back calibration ride. I post here the following ride and would like to know if it is OK.

Best regards.

Thanks.
Attachments
iBike_11_17_2018_0601_57_Miles.ibr
(650.69 KiB) Downloaded 153 times
Velocomp
Velocomp CEO
Posts: 7793
Joined: Fri Jan 11, 2008 8:43 am

Re: New PP Calibration

Post by Velocomp »

Everything looks fine!

There appears to be a strong headwind on your return leg. Since you did a very long ride, it is entirely possible that wind conditions changed during the ride.
John Hamann
barnabeflores
Posts: 16
Joined: Sat Nov 17, 2018 5:47 am

Re: New PP Calibration

Post by barnabeflores »

Yes, there was a strong wind on my way back.

I didn´t feel it was that strong during the cal. process, but was concerned it could have messed up things.

Thanks and have a nice weekend.

B
barnabeflores
Posts: 16
Joined: Sat Nov 17, 2018 5:47 am

Re: New PP Calibration

Post by barnabeflores »

Hi again,

Last week I paired PP to another bike (and sensors), but today when I returned to the first bike the PP didn´t recognize the sensors. I pressed PP after all the sensors were paired with the Garmin and the light was a steady red. Tried it a few more times and the same happened. I had to do another cal ride.

Is this normal?

Thanks.

B

PS - I have the 641 firmware in PP
Velocomp
Velocomp CEO
Posts: 7793
Joined: Fri Jan 11, 2008 8:43 am

Re: New PP Calibration

Post by Velocomp »

Please do the following:

1) Connect PP to Isaac

2) Go to Edit/Edit Profiles/Extract from Device.

3) Export this profile and post it in the thread

If you are using more than one bike, have you created a separate profile for each? If so, please repeat steps 1 through 3 for the other profile. Please mark clearly which profile is which!
John Hamann
barnabeflores
Posts: 16
Joined: Sat Nov 17, 2018 5:47 am

Re: New PP Calibration

Post by barnabeflores »

Hi again John.

Here is the file.

I would like to change the calibration weight to 83kg. Should I do: Edit profile/ Advanced/ change the weight/Accept/ Send to device?

Best regards.

B
Attachments
Bike n.1 profile.ibp
(431 Bytes) Downloaded 125 times
Velocomp
Velocomp CEO
Posts: 7793
Joined: Fri Jan 11, 2008 8:43 am

Re: New PP Calibration

Post by Velocomp »

Do you have a separate profile for each bike (for example, bike 1 is profile 1; bike 2 is profile 2)?

If you do not have separate profiles, then you should make them! This way you won't have to recalibrate every time you switch bikes.
John Hamann
barnabeflores
Posts: 16
Joined: Sat Nov 17, 2018 5:47 am

Re: New PP Calibration

Post by barnabeflores »

These are my doubts using the 641 firmware:

1 - Can I do what I mentioned in my last post to change settings in the same profile (ex. if I loose weight);

2 - To add another profile/ bike do I press PP for 4 sec to do an OB ride with the new bike/ sensors and then extract the ride from PP or,

2.1 - Do I previously create a profile using Isaac, send it to PP, do the OB ride and then extract the file?

Thanks.

B
Velocomp
Velocomp CEO
Posts: 7793
Joined: Fri Jan 11, 2008 8:43 am

Re: New PP Calibration

Post by Velocomp »

You will use Isaac to set up a new profile:

1) Connect PP to Isaac

2) Go to Device/Device Setup

3) Note the profile that your PP is using currently (probably profile 1)

4) Select a new profile (I suggest profile 2, but any profile is OK)

5) Follow the screens to enter the parameters for bike 2

6) After exiting the profile for bike 2, pair sensors for bike to to PP (MAKE SURE YOU ARE 100 FT AWAY FROM BIKE 1 SENSORS)

7) Do a calibration ride for bike 1

You will now have profile 1 for bike 1, and profile 2 for bike 2. Assuming that you are using different speed sensors for bike 1 and 2, PP will automatically switch between them.
John Hamann
barnabeflores
Posts: 16
Joined: Sat Nov 17, 2018 5:47 am

Re: New PP Calibration

Post by barnabeflores »

Got it John :D

Thanks for your time and help.

B
Post Reply