Transmitting Power to multiple devices?
Transmitting Power to multiple devices?
Hi,
I have a PPv4
I'm using the Wahoo Fitness App on my galaxy S10 as a cycling computer. (sensors pair over ANT+ not BLE)
I also use my Garmin 935 watch to record cycling activities.
I cannot pair both my Garmin and Wahoo app to the PowerPod simultaneously. Should this be supported? Does the PP take GPS /Elevation from the connected computer?
I have a PPv4
I'm using the Wahoo Fitness App on my galaxy S10 as a cycling computer. (sensors pair over ANT+ not BLE)
I also use my Garmin 935 watch to record cycling activities.
I cannot pair both my Garmin and Wahoo app to the PowerPod simultaneously. Should this be supported? Does the PP take GPS /Elevation from the connected computer?
Re: Transmitting Power to multiple devices?
Yes.
No. You need to use the NT tracker app, or you can merge GPS data from your bike computer into Isaac.
No. You need to use the NT tracker app, or you can merge GPS data from your bike computer into Isaac.
John Hamann
Re: Transmitting Power to multiple devices?
Hi John,
So I understand. The PP can send power data to multiple devices over ANT+? and or BLE?
the problem I have is when I begin a ride power will show on either my Garmin or Wahoo App. If I disconnect from one source power will show on the other and vice versa . I cannot display Power on both devices simultaneously.
My phone / Wahoo App is using ANT+
So I understand. The PP can send power data to multiple devices over ANT+? and or BLE?
the problem I have is when I begin a ride power will show on either my Garmin or Wahoo App. If I disconnect from one source power will show on the other and vice versa . I cannot display Power on both devices simultaneously.
My phone / Wahoo App is using ANT+
Re: Transmitting Power to multiple devices?
Over ANT+ it is unlimited.
Over BLE you can transmit (pair) to one device only.
Make sure your Garmin is paired by ANT+ to PP.
Over BLE you can transmit (pair) to one device only.
Make sure your Garmin is paired by ANT+ to PP.
John Hamann
Re: Transmitting Power to multiple devices?
Thanks John,
Yes, on closer inspection PP is using BLE to connect to my phone / Wahoo App
My Garmin is also defaulting to connect to PP via BLE - is there a trick to pair via ANT+?
Yes, on closer inspection PP is using BLE to connect to my phone / Wahoo App
My Garmin is also defaulting to connect to PP via BLE - is there a trick to pair via ANT+?
Re: Transmitting Power to multiple devices?
You'll need to read your Garmin instructions.
John Hamann
- lorduintah
- Posts: 648
- Joined: Fri Jan 11, 2008 9:37 am
- Location: Plymouth, MN
Re: Transmitting Power to multiple devices?
Suggestion -
After reading the Garmin instructions....
For each sensor you pair to a Garmin, you can get information about that sensor and in there are DETAILS. Within the DETAILS you will find how the sensor is communicating - ANT+ or Bluetooth Low Energy (BLE).
For some sensors both are possible, but the details will be one or the other for the sensor ID you select.
Delete the sensor, if it shows up as BLE and then the ANT+ version will be the only one connected.
See:
https://forums.garmin.com/sports-fitnes ... al-sensors
Tom
After reading the Garmin instructions....
For each sensor you pair to a Garmin, you can get information about that sensor and in there are DETAILS. Within the DETAILS you will find how the sensor is communicating - ANT+ or Bluetooth Low Energy (BLE).
For some sensors both are possible, but the details will be one or the other for the sensor ID you select.
Delete the sensor, if it shows up as BLE and then the ANT+ version will be the only one connected.
See:
https://forums.garmin.com/sports-fitnes ... al-sensors
Tom
Re: Transmitting Power to multiple devices?
Thanks Tom,
Yes the sensor is showing as connected by BLE under details, I also found out the Wahoo App on my phone now only uses BLE (even though ANT+ is supported on my phone) This explains why I can only view on one or the other.
1. I have tried disabling and or removing the PP on my Garmin and searching again hoping to pick-up ANT+ without success.
2. I have tried another cycling computer App that DOES support ANT+ I have confirmed by disabling BLE on my android phone and connecting my HRM - unfortunately it cannot find the PP
Both my Garmin and Android phone apps find the PP by BLE almost instantly. Is there a procedure for connecting ANT+? does the PP have to be transmitting Power?
Interestingly on my Wahoo App all connected sensors display a ANT ID, however, for the PP the ANT ID is - 1
Yes the sensor is showing as connected by BLE under details, I also found out the Wahoo App on my phone now only uses BLE (even though ANT+ is supported on my phone) This explains why I can only view on one or the other.
1. I have tried disabling and or removing the PP on my Garmin and searching again hoping to pick-up ANT+ without success.
2. I have tried another cycling computer App that DOES support ANT+ I have confirmed by disabling BLE on my android phone and connecting my HRM - unfortunately it cannot find the PP
Both my Garmin and Android phone apps find the PP by BLE almost instantly. Is there a procedure for connecting ANT+? does the PP have to be transmitting Power?
Interestingly on my Wahoo App all connected sensors display a ANT ID, however, for the PP the ANT ID is - 1
- Attachments
-
- Screenshot_20210808-075926_Wahoo.jpg (34.71 KiB) Viewed 7355 times
-
- 20210808_073904.jpg (171.11 KiB) Viewed 7357 times
-
- Screenshot_20210808-074033_Jepster.jpg (31.41 KiB) Viewed 7358 times
Last edited by Thomas on Sat Aug 07, 2021 11:30 pm, edited 1 time in total.
Re: Transmitting Power to multiple devices?
PP has to be awake and paired to its speed sensor (solid green) prior to starting any ANT+ bike computer pairing process.
I have no knowledge of how the Garmin (or Wahoo) devices do their pairing procedures. I suggest you consult their technical support pages.
I have no knowledge of how the Garmin (or Wahoo) devices do their pairing procedures. I suggest you consult their technical support pages.
John Hamann
Re: Transmitting Power to multiple devices?
I just learnt that with Garmin both ANT + BLE sensors are shown simultaneously when searching. By default ANT is shown first then BLE. I have been unnecessarily connecting both ANT + BLE on dual transmitting devices.
Example for my dual transmitting Speed Sensor it first shows ANT then if I select "show bluetooth devices" I can connect BLE too.
I'll try mounting PP and ensure it's connected to speed sensor and try again
Example for my dual transmitting Speed Sensor it first shows ANT then if I select "show bluetooth devices" I can connect BLE too.
I'll try mounting PP and ensure it's connected to speed sensor and try again
- Attachments
-
- 20210808_092802.jpg (197.42 KiB) Viewed 7352 times
Re: Transmitting Power to multiple devices?
When I mount the PP wake up the speed sensor and click the button once the light shows solid Red then turns off.
- Attachments
-
- 20210808_094151.jpg (139.03 KiB) Viewed 7349 times
Re: Transmitting Power to multiple devices?
If I connect the PP to my PC then "Get from Device" under my profile--> wireless sensors it appears all connected sensors are now forgotten..
But if I hold the button down for 4 seconds to get flashing green light , it just stays flashing for around 2 minutes and never connects.... I'll try a factory reset again.
But if I hold the button down for 4 seconds to get flashing green light , it just stays flashing for around 2 minutes and never connects.... I'll try a factory reset again.
- Attachments
-
- Screenshot 2021-08-08 101820.png (39.02 KiB) Viewed 7348 times
Re: Transmitting Power to multiple devices?
SUCCESS!!
No factory reset
1. I restored profile and sent to device (restored wireless IDs too).?
2. Woke up Speed Sensor
3. Clicked PP button Once. The light shows solid YELLOW
4. searched for sensor on garmin and there it is
No factory reset
1. I restored profile and sent to device (restored wireless IDs too).?
2. Woke up Speed Sensor
3. Clicked PP button Once. The light shows solid YELLOW
4. searched for sensor on garmin and there it is
- Attachments
-
- 20210808_104219.jpg (202.03 KiB) Viewed 7348 times
-
- 20210808_104210.jpg (236.55 KiB) Viewed 7348 times
Re: Transmitting Power to multiple devices?
Re calibrated and transmitting to both devices simultaneously
- Attachments
-
- 20210808_154620.jpg (96.32 KiB) Viewed 7323 times
-
- Screenshot_20210808-160608_Wahoo.jpg (51.9 KiB) Viewed 7324 times
Re: Transmitting Power to multiple devices?
Loving the data from the Connect IQ App
- Attachments
-
- Screenshot_20210808-183450_Connect.jpg (45.43 KiB) Viewed 7322 times
- lorduintah
- Posts: 648
- Joined: Fri Jan 11, 2008 9:37 am
- Location: Plymouth, MN
Re: Transmitting Power to multiple devices?
Although I use a Garmin Edge 830 and not a wrist watch device - I have found that the only reliable pairing of my Garmin and PP to the speed/cadence sensors comes from waking the speed and cadence sensors, then one-click on the PP to wake it up. Just a few seconds later I get the solid green on the PP indicating is has found the sensors and is communicating only then do I turn on the Garmin.
So the oder is: sensors -> PP -> Garmin. Now for a Wahoo or other bike computer I have no experience.
A few times I had turned on the Garmin earlier - but then is sometimes would pair to BLE.
So the oder is: sensors -> PP -> Garmin. Now for a Wahoo or other bike computer I have no experience.
A few times I had turned on the Garmin earlier - but then is sometimes would pair to BLE.
Re: Transmitting Power to multiple devices?
This is good advice.lorduintah wrote: ↑Sun Aug 08, 2021 11:15 am Although I use a Garmin Edge 830 and not a wrist watch device - I have found that the only reliable pairing of my Garmin and PP to the speed/cadence sensors comes from waking the speed and cadence sensors, then one-click on the PP to wake it up. Just a few seconds later I get the solid green on the PP indicating is has found the sensors and is communicating only then do I turn on the Garmin.
So the oder is: sensors -> PP -> Garmin. Now for a Wahoo or other bike computer I have no experience.
A few times I had turned on the Garmin earlier - but then is sometimes would pair to BLE.
The instant PP is turned on it begins transmitting in BLE mode. So, any bike computer would see PP as a BLE power meter and pair immediately using the BLE channel.
ANT+ is NOT turned on the instant PP is turned on. Instead, PP must first "find" the speed sensor (indicated by solid green light). Only AFTER the speed sensor is found will the PP ANT+ mode be enabled.
John Hamann
Re: Transmitting Power to multiple devices?
Yes, this was why I was getting confused.
BLE showed instantly by simply turning on the PP without waking the Speed Sensor (it was on my desk next to my computer) this left me thinking there was a pairing issue
Thanks John and Tom
BLE showed instantly by simply turning on the PP without waking the Speed Sensor (it was on my desk next to my computer) this left me thinking there was a pairing issue
Thanks John and Tom
Re: Transmitting Power to multiple devices?
This graphic is from the Garmin Connect app, right?
Mine looks totally different, so wondering now if I have something that needs addressing or configure differently
Thanks
- Attachments
-
- IMG_0006.PNG (108.85 KiB) Viewed 6856 times