AeroPod, PowerPod and Newton

Thanks John, Email sent.

Ken B.

Hello John. I emailed tech support last Friday, no response yet. Could you assist , thank you.
Ken B

Quick update. I tried a O&B cal ride during my ride this morning. This time , I got a red at 50 and returned to start. After 100 flashing red then flashing Re/green numbers starting at 50. after some time, everything settled down and started reporting normal numbers. Totally strange. But no ride...

Good Morning John. Starting from scratch, I performed a Device>Setup>rest>profile device . 1. Paired all sensors (PP and sensors charged) 2. Solid gree, then solid yellow. 3.Set off, no flashing red/green. 4. Did a hard reset at staring point. Then got solid green, solid yellow/ followed by flashing...

Only 1 little issue, John. I can't make that profile go into the PP. I set that Profile of say Profile #1, it remains "Factory Default" . Profile Ciocc 5 13 2024 will set .

Ok, John. I have a 17 mile ride plan anyway, for tomorrow with this bike. Will post when return.
Thank you.

only extracted a profile

Ok John, not very good results, but this is what happen. 1. All sensors fresh batts and PP charged 2. Paired Sensors . OK (verified on Garmin) 3. Solid yellow light. after minute, still solid yellow, no flashing Red/green 4, Hard reset, Sensors paired, Solid yellow ,then Flashing Red/Green. 5. Start...

Thanks John, I carry Instructions with me now ,when having this issues. Will try, before rain sets in.

Ken

Ok, re read instructions .
1. All current profiles are backed up and in Isaac.
2. All profiles now are "factory default ".per the above setup instructions.
3. Ready to start bike #1.
Again , what do I do, if at the end of O&B , I see the red/green flashing light .
Thanks. KB

Ok, to understand, the ride i performed on the Concorde is not good, although was able to extract a profile ?? All my profiles are in Isaac, under Edit Profiles and currently named. Now keep in mind, I can only use #1 and #2, as you explained, there is a technical issue with #3 & #4. Explained l...

Okay, John. Discovered another issue and paid attention this time. Needed to calibrate Concorde, as it had same speed sensor ID as does the Merit. (Mentioned above) . PP found all 3 sensors, light turned solid yellow, but after riding to starting point , over a minute, refused to start flashing Red/...

Hello John, No, I performed the ride delete command, as requested, yesterday. And not from todays ride, using the Ciocc Profile for that bike. The past ride that records , was the Merit on 5/19/2024. All rides this year , with the Merit have recorded . Remember, These 2 bikes have a new cadence sens...

Hello John,

Road 14mi. PP was putting out watts , but nothing to download. Still using the Ciocc 5 13 2024 Prof 2.

I've added 2 other profiles associated with this bike that didn't seem to work, can't remember issue.

Thanks John. I'll let you know tomorrow, how it goes. Again, thanks.

Ken B.

Done . Will ride tomorrow and report back with results .

Thanks, Ken b

Thanks John, But, which ride file am I erasing ?

Ken B.

Edit: Device>erase all ride data ????

Hello John, Another data point. Today I set profile 1 for the Merit (which I had completed a O&B calibration in April. ) Took a short 8 mi. ride and the ride was recorded in Isaac . So, my guess is, the issue is with the Ciocc profile and calibration. What's strange, as mentioned earlier, PP fin...

Hello John, Just an update. Todays ride, was all normal. Woke up all sensors, PP blinked green, found all sensors , solid green, started riding . Within a minute , normal watts were being displayed, and continued to display normal watts through out the complete ride. All data in my Garmin (530 Plus...

Hello John, Just an update. Todays ride, was all normal. Woke up all sensors, PP blinked green, found all sensors , solid green, started riding . Within a minute , normal watts were being displayed, and continued to display normal watts through out the complete ride. All data in my Garmin (530 Plus)...

Final page of data.

Continuation

Continuation

Hello John, That's a lot of homework, anyway...... So today, I headed out with same bike with issue. Green light came on, then turned solid yellow. Rode short distance, thinking it wanted to recal , nothing. I turned off, restarted, same solid yellow light. After a short distance , i could see the r...

Hello John, Installed a new cadence sensor, so I had to do a recalibration . O&B ride, seemed to complete, then headed out for a 11 mile ride. Garmin was reading reading power data, nothing weird happening . Numbers looked normal for the ride, but when into Isaac to extract profile from the ride...

Thank you John . So maybe, with the memory being full, this might have caused the high watt numbers ? Also, when you say , keep PP attached to bike, what will happen when I move to another bike ? One with a profile installed in the PP ? This current bike will be ridden till I'm done for the year . T...

Hello John, This is strange to me, but you'll know what happen. As you will see, the wattage was off my chart at first, then returned to normal for the duration of a short ride. The previous 2 rides (that did not record) stayed high, until I shut off the PP. This is the only ride , stored in the PP....

Thanks John. I have deleted all ride files. As soon as the temps get above freezing, I'll ride around the block. In the mean time, I'm done for the season. Ken

Looks to be 50 on Friday.

Hello John, The last 2 days, my PP has been displaying 500, 1000 2500+ WATTS. Yesterdays ride, all was functioning normal, then I made a stop 3miles from home. After continuing the ride, the PP was displaying very high watts. Today, at the start, immediately starting showing very high numbers. I did...

Thank you, John. Next time, if there is one, ill use a clock to count out those 12 sec.

Again, thank you, glad if wasn't serious.

Ken B.