Power very fluctuating so I did a calibration ride but...
Power very fluctuating so I did a calibration ride but...
Hi, I need some help here as I have a feeling that something is wrong...
I am using the PowerPod with two bikes a street one (Scott Speedster 10) and MTB (Cube LTD Pro). Lately the profile for the road one is giving me very high fluctuations so today I did a calibration ride. It was some wind during the calibration ride so I would appreciate if someone could check the calibration profile attached here.
Main differences between previous calibration are:
Aero 0.620 before 0.362
Wind scaling 1.712 before 1.000
With the new calibration I am either getting higher overall Power values, but stable values during workout then I could see the day before. If I run Check Calibration on this last run I am getting a suggestion to change average power from 220W to 190W. So not sure what to do next. Maybe the fact that it was some wind during calibration ride was not good. I have also attached the profile and the run.
Note: I updated the numbers (I was looking at the wrong screen)
Thanks,
Serban
I am using the PowerPod with two bikes a street one (Scott Speedster 10) and MTB (Cube LTD Pro). Lately the profile for the road one is giving me very high fluctuations so today I did a calibration ride. It was some wind during the calibration ride so I would appreciate if someone could check the calibration profile attached here.
Main differences between previous calibration are:
Aero 0.620 before 0.362
Wind scaling 1.712 before 1.000
With the new calibration I am either getting higher overall Power values, but stable values during workout then I could see the day before. If I run Check Calibration on this last run I am getting a suggestion to change average power from 220W to 190W. So not sure what to do next. Maybe the fact that it was some wind during calibration ride was not good. I have also attached the profile and the run.
Note: I updated the numbers (I was looking at the wrong screen)
Thanks,
Serban
- Attachments
-
- Scott dupa calibrare pe strada 10oct19.ibp
- (370 Bytes) Downloaded 156 times
-
- iBike_10_10_2019_0941_24_Miles_HiDef.ibr
- (761.87 KiB) Downloaded 177 times
Re: Power very fluctuating so I did a calibration ride but...
You have an out-and-back ride, with a long symmetrical section between minute 24 and 54. I adjusted your profile so that wind speed was the same in this section.
This dropped your watts some, but I think this looks good.
Corrected profile and ride file attached.
This dropped your watts some, but I think this looks good.
Corrected profile and ride file attached.
- Attachments
-
- Meste_Corr_10_10_2019_0941_24_Miles_HiDef.ibr
- (839.16 KiB) Downloaded 194 times
-
- Meste.ibp
- (425 Bytes) Downloaded 177 times
John Hamann
Re: Power very fluctuating so I did a calibration ride but...
With this one the average power drops from 226 to 173W, if you think this is ok, then I would use it, but I definetely felt more tired than this average...
Re: Power very fluctuating so I did a calibration ride but...
John, I remember reading somewhere that there is a button combination to start a Calibration Ride while out on a ride. Was I dreaming and there is only the procedure that has to be started from the computer?
Re: Power very fluctuating so I did a calibration ride but...
I found an old reply also from you in this forum: If you are using FW 641, you can most definitely calibrate on the fly, without using Isaac. You press-hold the button for 4 seconds, to do a new scan (make sure there are no other bikes close by). The scan will force PP into an O&B calibration.
thanks
thanks
Re: Power very fluctuating so I did a calibration ride but...
But I still have a question:
I go out on a ride with PP recording, Than I reach the place I want to do a calibration. As PP is still recording and do not want to wait till it goes automatically on hybernation, how do I stop the recording and start O&B calibration? This is where I am not sure.
I go out on a ride with PP recording, Than I reach the place I want to do a calibration. As PP is still recording and do not want to wait till it goes automatically on hybernation, how do I stop the recording and start O&B calibration? This is where I am not sure.
Re: Power very fluctuating so I did a calibration ride but...
Correctmeste wrote: ↑Thu Oct 10, 2019 12:39 pm I found an old reply also from you in this forum: If you are using FW 641, you can most definitely calibrate on the fly, without using Isaac. You press-hold the button for 4 seconds, to do a new scan (make sure there are no other bikes close by). The scan will force PP into an O&B calibration.
thanks
John Hamann
Re: Power very fluctuating so I did a calibration ride but...
Press-hold for 4 seconds. This will stop the current ride, cause a sensor pairing, and put PP into calibration mode.meste wrote: ↑Thu Oct 10, 2019 12:41 pm But I still have a question:
I go out on a ride with PP recording, Than I reach the place I want to do a calibration. As PP is still recording and do not want to wait till it goes automatically on hybernation, how do I stop the recording and start O&B calibration? This is where I am not sure.
John Hamann
Re: Power very fluctuating so I did a calibration ride but...
Hi John,
Today is a sunny with no wind day so I went out and did a calibration ride which came with these results:
Aero 0.366
Wind Scaling 1.000
CdA 0.366
Fric 11.212
The one that you amended it for me after that ride was:
Aero 0.439
Wind Scaling 1.212
CdA 0.362
Fric 11.158
If I apply this new calibration to my ride from yesterday, I will get even lower power values, for example PWR 20min drops from 283W (which was a way too high) to 193W which I believe is low (actually I am starting to question my feelings as well...)
I am not sure what to do, the power values are so different and was hoping that after today's calibration with no wind and sunny on a flat road with no traffic to finally solve this matter.
What would you suggest me to do?
Thanks (attached todays calibration profile)
Serban
Today is a sunny with no wind day so I went out and did a calibration ride which came with these results:
Aero 0.366
Wind Scaling 1.000
CdA 0.366
Fric 11.212
The one that you amended it for me after that ride was:
Aero 0.439
Wind Scaling 1.212
CdA 0.362
Fric 11.158
If I apply this new calibration to my ride from yesterday, I will get even lower power values, for example PWR 20min drops from 283W (which was a way too high) to 193W which I believe is low (actually I am starting to question my feelings as well...)
I am not sure what to do, the power values are so different and was hoping that after today's calibration with no wind and sunny on a flat road with no traffic to finally solve this matter.
What would you suggest me to do?
Thanks (attached todays calibration profile)
Serban
- Attachments
-
- Scott Calibration Ride Herastrau.ibp
- (421 Bytes) Downloaded 172 times
Re: Power very fluctuating so I did a calibration ride but...
Please post .ibr ride file
John Hamann
Re: Power very fluctuating so I did a calibration ride but...
Today I simply went home after the calibration so not much a ride, but I have attached.
- Attachments
-
- iBike_10_11_2019_1148_1_Miles_HiDef.ibr
- (72.02 KiB) Downloaded 173 times
Re: Power very fluctuating so I did a calibration ride but...
Your measured profile is very, very close to the corrected profile I gave you.
Your measured profile is fine.
Your measured profile is fine.
John Hamann