Search found 21 matches

by faheyb
Tue Mar 08, 2016 11:48 pm
Forum: Newton Setup
Topic: Multiple Profiles multiple bikes
Replies: 3
Views: 8701

Re: Multiple Profiles multiple bikes

I am attempting to use the same bike ( same Speed and Cad sensors) with different wheel dia, weight and a minor change to the Aero and CdA and expected that I would have the ability to select either P1 or P2 manually once the Newton picked up the sensors on the bike, but it will only default to one ...
by faheyb
Tue Mar 08, 2016 12:15 am
Forum: Newton Setup
Topic: Multiple Profiles multiple bikes
Replies: 3
Views: 8701

Multiple Profiles multiple bikes

I have used 3 different profiles on my 3 bike for some time. The Newton with FW 5.0 automatically selects the correct profile. Recently I converted some of my wheel sets from 23mm to 25mm circ. and have attempted to set up an alternative profile for my race bike, with 23mm tubs as 1 profile and 25mm...
by faheyb
Tue Nov 05, 2013 1:43 am
Forum: Newton Setup
Topic: Repeat Profile following Stem change
Replies: 1
Views: 3121

Repeat Profile following Stem change

I have run my Newton on two similar bikes for 18 months or so and have been reasonably happy with the profiles. Recently I went through a bike fit , following a ski injury, and will now need a slight change to my stem angle (the only significant change was a 2 deg increase in rise, same bars) Is it ...
by faheyb
Thu Jan 17, 2013 2:18 am
Forum: Newton Technical Support
Topic: Saving Ride Files
Replies: 1
Views: 2348

Saving Ride Files

For the last 18 months or so, I have saved my iBike ride files by exporting as CSV files, rather than IBR files. My reasoning was that I like to retain all ride files so that they are accessable by the iBike SW, previously GEN3 and now ISSAC, AND transfer all ride files to Training Peaks at the time...
by faheyb
Tue Dec 18, 2012 3:36 am
Forum: Newton Technical Support
Topic: Drafting
Replies: 4
Views: 4313

Re: Drafting

Thanks for the feedback. It may be that my profiles (2 bikes) are not perfect, but I feel that at times the power readings are just too low on a ride I frequetly repeat and on downloading I see the question re drafting. Knowing that there was no drafting and that I did an out and back ride. I fix it...
by faheyb
Sat Dec 15, 2012 9:55 pm
Forum: Newton Technical Support
Topic: Drafting
Replies: 4
Views: 4313

Drafting

I have noticed during ride downloads the "% drafting" check has become too frequent, following out and back rides, when I am alone. This can be corrected through the SW with the resulting significant increases for AP, NP, IF, TSS. Following that I have monitored several Group rides, when a...
by faheyb
Sat Nov 17, 2012 8:43 pm
Forum: Newton Technical Support
Topic: iBike not responding to download
Replies: 3
Views: 3624

Re: iBike not responding to download

Have completed a hard reset, and then reset time and date. BUT the result is just the same, there appears to be no connection between the SW and the Newton. I then went through the device connect tab to check on any connection between SW and the Newton, this subsequently directed me to rescan and th...
by faheyb
Sat Nov 17, 2012 6:53 pm
Forum: Newton Technical Support
Topic: iBike not responding to download
Replies: 3
Views: 3624

iBike not responding to download

I have a new issue with downloading from my Newton to the PC, and received the dreaded "ibike unit not responding." It has not shown any issues in the previous 4 months. I had my first wet ride today, but no signs of the aero port blockage, the tab over the USB connector on the Newton rema...
by faheyb
Sat Sep 08, 2012 6:30 am
Forum: Newton Setup
Topic: Cal Ride and Coast Downs
Replies: 13
Views: 9063

Re: Cal Ride and Coast Downs

Many thanks, I can not believe I missed that.
by faheyb
Fri Sep 07, 2012 4:41 pm
Forum: Newton Setup
Topic: Cal Ride and Coast Downs
Replies: 13
Views: 9063

Re: Cal Ride and Coast Downs

John, I don't quite understand. I completed 4 calibration rides, 2 in the drops and 2 on the hoods, and then ran a serries od 10 coastdowns in both positions, a total of 20. My issue was in getting the data into the software for analysis. There is not access to Setup/Download Coastdowns in my Isaac ...
by faheyb
Fri Sep 07, 2012 4:39 am
Forum: Newton Setup
Topic: Cal Ride and Coast Downs
Replies: 13
Views: 9063

Cal Ride and Coast Downs

I finally managed to complete a set of Calibration rides, 2 in the Drops and 2 on the Hoods. The Calib rides are reasonably similar and not too dissimilar from my iAero on the same bike. I have downloaded the Calib rides and coastdowns as both ibr and csv files, but I'm struggling to work out how to...
by faheyb
Thu Sep 06, 2012 3:24 am
Forum: Newton General Questions
Topic: Cross Fin for Newton
Replies: 2
Views: 4070

Cross Fin for Newton

I just unpacked my Newton, along with an additional dual mount and universal mount for the TT bike as well as the RMS. There is no evidence of the Cross Fin of which I was sure would improve results on windy days and in the bunch. Please advise on results with and without the cross fin and I hope Ve...
by faheyb
Tue Aug 28, 2012 5:33 am
Forum: Frequently Asked Questions
Topic: Isaac SW failed to load
Replies: 1
Views: 3056

Re: Isaac SW failed to load

I finally worked it out. I actually do not know why it did not automatically load and run, but on un-installing all remaining and new downloads and starting again - all is good. Now I just need my Newton to arrive and then I will have my hands full in setting up all bikes.

Many Thanks
by faheyb
Mon Aug 27, 2012 3:08 pm
Forum: Frequently Asked Questions
Topic: Isaac SW failed to load
Replies: 1
Views: 3056

Isaac SW failed to load

On updating from version 6.1.2 to Issac 7.1.2 all seemed to be going well until it got to the start to install, where the Installation Summary "to be reviewed" listed "No SW will be installed or removed" and at the bottom of the screen the only options were "Save file, "...
by faheyb
Sat Aug 25, 2012 8:14 pm
Forum: Newton Technical Support
Topic: Isaac and IBike SW
Replies: 2
Views: 2983

Isaac and IBike SW

I have recently ordered a Newton and would like to continue to use my iAero on my MTB and possibly for wet training rides on the road. It appears that for Mac users this may be possible, but what for Windows users. Could I actually load the Isaac SW onto my Windows 7 based PC, along with the GenIII ...
by faheyb
Tue Aug 21, 2012 3:22 am
Forum: Gen III troubleshooting
Topic: Centre Button not responding
Replies: 1
Views: 8038

Centre Button not responding

:( I have used my iAero quite sucessfully on 4 bikes, including a TT bike and a MTB. Today the centre button appeared fail. The 4 others, Total Avg-Max, Enviro and Hill-Wind seem to be perfectly alright. I removed the battery and performed a hard reset (a couple of times) without success. I complete...
by faheyb
Thu Mar 29, 2012 3:05 am
Forum: Wireless Troubleshooting
Topic: WLS Fail
Replies: 2
Views: 9060

WLS Fail

I have run an iAero on 3 different bikes since late 2010. Recently I replaced a wireless transmitter after the strap broke. After 3 months use the replacement failed, while the other 2 remain scanning perfectly. The symptom is the "WLS Fail". Initially I replaced the batteries on the iAero...
by faheyb
Fri Mar 09, 2012 3:38 pm
Forum: Frequently Asked Questions
Topic: Software updates
Replies: 2
Views: 3517

Re: Software updates

This first occurred 2 months ago and the situation has not changed. I have just not bothered to find the fault and continue to use 6.0.0. The PC error message states "either the server is not available right now, or your computer is not connected to the internet". I can set up the portable...
by faheyb
Fri Mar 09, 2012 2:52 am
Forum: Frequently Asked Questions
Topic: Software updates
Replies: 2
Views: 3517

Software updates

I have 6.0.0 on my PC and 6.1.0 on my laptop and for some reason the ibike SW appears to find the PC "not connected to the internet" and hence I am unable to update my SW, HW etc. Could you please advise on a fix or another way of acessing the updates through the iBike site. Thanks in adva...
by faheyb
Fri Nov 04, 2011 5:21 pm
Forum: Wireless Troubleshooting
Topic: iAero shutting off while waiting for race start
Replies: 2
Views: 9374

Re: iAero shutting off while waiting for race start

Thanks for the reply. I have updated to 4.26, and replaced all batteries. I have also checked the 20 minute time period several times. It is now perfect.

Thanks.
by faheyb
Sun Oct 30, 2011 3:30 am
Forum: Wireless Troubleshooting
Topic: iAero shutting off while waiting for race start
Replies: 2
Views: 9374

iAero shutting off while waiting for race start

I have been using an iAero for 15 months and successfully use it on 4 bikes, including a TT bike and a MTB. I find that I need to run a scan every time I change bikes, but it will recognise the sensors if used on the same bike in sucession. I assume that this is normal. Recently I have an issue with...